During the working process of the generator set, a small amount of waste and small solid particles are produced, and the main harm is noise. Its sound value is about 108 dB, which seriously affects people's normal work and life.

發電機組房消音環保工程需要根據機房的具體情況進行設計和施工。為了保障機組的正常工作，在設計發電機組房消音工程時，需要注意以下幾個方面:

The noise elimination and environmental protection project of generator set room needs to be designed and constructed according to the specific conditions of the machine room. In order to ensure the normal operation of the unit, the following aspects should be paid attention to when designing the silencing project of generator set room:

1.系統:機房?jī)?nèi)不得設置燃油箱，不得堆放易燃易爆物品、要配置消防器材.同時，井聯電柜等電氣設備要與發電機組房隔離開來，以免影響電氣元件的工作壽命。

1. System: fuel tank shall not be set in the machine room, inflammable and explosive articles shall not be stacked, and fire-fighting equipment shall be equipped At the same time, electrical equipment such as well connection cabinet shall be isolated from the generator set room to avoid affecting the working life of electrical components.

2.進風系統:每臺發電機組工作時需要大量的新鮮空氣,所以機房有足夠的進風。

2. Air inlet system: each generator unit needs a lot of fresh air during operation, so there is enough air inlet in the machine room.

3.排風系統:發電機組工作時，鏟生大量的熱量，為便發電機組能正常工作,機房環境溫度不得超過50握氏度，而對柴油機奧好的工況來說，機房環境溫度應低于37.8攝氏度， 所經要抽部分熱量出機房。發電機組房隔音工程的主要內容:

3. Exhaust system: when the generator set is working, it generates a lot of heat. In order to make the generator set work normally, the ambient temperature of the machine room shall not exceed 50 ° C. for the excellent working condition of the diesel engine, the ambient temperature of the machine room shall be lower than 37.8 ° C, and part of the heat shall be pumped out of the machine room. Main contents of sound insulation works of generator set room:

1.機房出入通道的隔音:本著方便發電機組調入、調出及機房人員工作方便的原則來設置-個或二個隔音門，以金屬構架，內附高質量隔音材料,度以8cm至12cm為宜.

1. Sound insulation of the entrance and exit of the machine room: one or two sound insulation doors shall be set in the principle of facilitating the transfer in and out of the generator set and the work of the machine room personnel. They shall be metal frame with high-quality sound insulation materials inside, and the degree shall be 8cm to 12cm

2.進風系統的隔音:在進風面設置消音槽和隔音墻，采取強制進風方式以保持機組正常運行所需的新鮮空氣。

2. Sound insulation of air inlet system: set silencing trough and sound insulation wall on the air inlet surface, and adopt forced air inlet mode to maintain fresh air required for normal operation of the unit.

3.排風系統的隔音。在排風面沒置消音槽和隔音墻，采取強制排風方式，以更大的限度降低發電機工作環境溫度。

3. Sound insulation of exhaust system. There is no silencing slot and sound insulation wall on the exhaust surface, and the forced exhaust mode is adopted to reduce the working ambient temperature of the generator to a greater extent.

4.煙道消聲系統:在機房外的煙管上安裝級阻尼式消音哭器，以降低發動機排煙噪聲,同時又要不影響廢氣的排放。

4. Flue silencing system: stage damping silencers are installed on the smoke pipes outside the machine room to reduce the exhaust noise of the engine without affecting the emission of exhaust gas.

5.吸音墻和吸音天花,在機房?jī)?nèi)寺上安裝吸盤音材料，以防止境音從機房頂傳出和回彈，降低室噪音分貝數。

5. For the sound-absorbing wall and ceiling, install sound-absorbing materials on the temple in the machine room to prevent the ambient sound from coming out and rebounding from the roof of the machine room and reduce the decibel of room noise.

本文的精彩內容由天然氣發電機組提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://m.dgtmcnc.com我們有專門的客服為您解答問題

The wonderful content of this article is provided by the natural gas generator set. There are many wonderful contents on this website. You can click to enter more contents: http://m.dgtmcnc.com We have special customer service to answer your questions