煉化尾氣發電機組常見故障及處理方法如下，綜合多個權威來源整理而成：

　　The common faults and troubleshooting methods of the refining tail gas generator set are as follows, compiled from multiple authoritative sources:

　　一啟動困難1

　　Difficulty Starting 1

　　電池問題 ：檢查電池電壓是否充足，電量不足需充電或更換電池

　　Battery issue: Check if the battery voltage is sufficient. If the battery is low, it needs to be charged or replaced

　　燃氣供應 ：確保燃氣閥門開啟且供應穩定，檢查燃氣管道無泄漏

　　Gas supply: Ensure that the gas valve is open and the supply is stable, and check that there are no leaks in the gas pipeline

　　點火系統 ：檢測點火線圈火花塞及控制模塊是否正常，必要時更換2

　　Ignition system: Check whether the ignition coil spark plug and control module are normal, and replace them if necessary

　　燃油系統 ：檢查燃料泵濾清器是否堵塞，氣瓶壓力是否正常

　　Fuel system: Check if the fuel pump filter is clogged and if the cylinder pressure is normal

　　二運行不穩定或電壓異常1

　　Unstable operation or abnormal voltage 1

　　控制系統故障 ：電壓調節器故障需維修或更換3

　　Control system malfunction: Voltage regulator malfunction requires repair or replacement

　　負載問題 ：負載過大導致電壓波動，需減少負載或升級設備

　　Load problem: Voltage fluctuation caused by excessive load, need to reduce load or upgrade equipment

　　散熱問題 ：冷卻液溫度傳感器故障或散熱不良，需檢查散熱器及風扇

　　Heat dissipation issue: The coolant temperature sensor is faulty or has poor heat dissipation. It is necessary to check the radiator and fan

　　三缸套水溫度異常

　　Abnormal water temperature of the three cylinder liners

　　冷卻系統故障 ：散熱器風扇或節溫器故障導致冷卻液循環不暢，需維修或更換

　　Cooling system malfunction: Poor circulation of coolant caused by radiator fan or thermostat malfunction, requiring repair or replacement

　　傳感器故障 ：溫度傳感器失靈需更換，確保顯示準確

　　Sensor malfunction: The temperature sensor is malfunctioning and needs to be replaced to ensure accurate display

　　四排氣溫度異常2

　　Abnormal exhaust temperature 2

　　排氣系統堵塞 ：排氣管路或消音器堵塞，需清理或更換1

　　Exhaust system blockage: The exhaust pipe or muffler is blocked and needs to be cleaned or replaced

　　負荷過大 ：調整負荷曲線，避免長時間高負荷運行

　　Overloading: Adjust the load curve to avoid prolonged high load operation

　　五爆震現象

　　Five detonation phenomena

　　燃氣質量 ：燃氣含雜質或水分，需清洗管道或安裝干燥器3

　　Gas quality: The gas contains impurities or moisture, and the pipeline needs to be cleaned or a dryer needs to be installed

　　熱值調整 ：熱值設置錯誤導致燃燒不充分，需重新校準

　　Heating value adjustment: Insufficient combustion caused by incorrect heating value setting, requiring recalibration

　　傳感器故障 ：爆震傳感器損壞需更換

　　Sensor malfunction: Knock sensor damaged and needs to be replaced

　　六功率不足

　　Insufficient power of six

　　燃氣供應不足 ：調壓閥堵塞或燃料濾清器臟污，需清理或更換

　　Insufficient gas supply: blocked pressure regulating valve or dirty fuel filter, needs to be cleaned or replaced

　　進氣系統故障 ：空氣濾清器堵塞或進氣管路漏氣，需清潔或修復1

　　Air intake system malfunction: clogged air filter or air leakage in intake pipeline, needs to be cleaned or repaired

　　機械磨損 ：長期高負荷運行導致發動機磨損，需定期維護4

　　Mechanical wear: Long term high load operation causes engine wear and requires regular maintenance

　　七噪音過大

　　7. Excessive noise

　　機械部件松動 ：地腳螺栓松動或底座不穩固，需加固

　　Loose mechanical components: Loose foundation bolts or unstable base, requiring reinforcement

　　積碳問題 ：發動機積碳嚴重，需專業清洗

　　Carbon deposition issue: The engine has severe carbon deposition and requires professional cleaning

　　八燃油系統故障4

　　Eight fuel system faults 4

　　油壓異常 ：油面過低需加油，油泵故障需維修

　　Abnormal oil pressure: The oil level is too low and needs to be refilled. The oil pump is malfunctioning and needs to be repaired

　　燃油濾清器堵塞 ：需更換濾清器，確保燃油供應暢通

　　Fuel filter clogged: filter needs to be replaced to ensure smooth fuel supply

　　維護保養建議

　　Maintenance suggestions

　　定期檢查 ：電池燃油點火系統及冷卻系統每月至少檢查一次

　　Regular inspection: The battery fuel ignition system and cooling system should be checked at least once a month

　　清潔保養 ：清除積碳油污，保持設備內部清潔

　　Cleaning and maintenance: remove carbon deposits and oil stains, and keep the interior of the equipment clean

　　更換易損件 ：濾芯密封件等需根據使用年限及時更換4

　　Replace vulnerable parts: filter element seals, etc. should be replaced in a timely manner according to their service life

　　若以上方法無法解決問題，建議聯系專業維修人員進行檢查和維修。

　　If the above methods cannot solve the problem, it is recommended to contact professional maintenance personnel for inspection and repair.

　　本文由 煉化尾氣發電機組  友情奉獻.更多有關的知識請點擊  http://m.dgtmcnc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the Refining and Chemical Exhaust Gas Generator Unit For more related knowledge, please click http://m.dgtmcnc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.