Large generator set is the most widely used power generation equipment in the market, which alleviates the tension of power consumption and brings convenience to people. The following is a brief analysis of the engine oil filter element by the generator manufacturer:

油濾芯結構簡單，其內部濾紙和一些重要的部分從外觀也很難區別。所以各種高仿濾芯層出不窮，而且價格低廉，故而有些用戶為了省錢就去購買偽劣品。機油濾芯一定要選擇正規的，如果沒有質量保證的濾芯使用以后將會引起機組故障，導致機組受損，一旦機器內部混入雜質，那可就得不償失了。

The structure of the oil filter element is simple, and it is difficult to distinguish its internal filter paper and some important parts from their appearance. Therefore, all kinds of high imitation filter elements emerge in endlessly, and the price is low. Therefore, some users buy fake and shoddy products in order to save money. The regular brand of engine oil filter element must be selected. If there is no quality assurance filter element, it will cause unit failure and damage. Once impurities are mixed into the machine, the gain is not worth the loss.

機油濾芯更換步驟：

Oil filter element replacement steps:

步：排出廢機油

Step 1: drain the waste engine oil

先把油箱里的廢機油排出，在油底殼下方放置舊油容器，打開放油螺栓，排出廢機油。排放機油的時候盡量讓機油多滴下一段時間，要保證廢油排放干凈。(機油通過使用，會產生很多雜質，如果在更換的時候排放不干凈，容易堵塞油路，造成供油不暢，造成結構件磨損。

First drain the waste oil in the oil tank, place the old oil container under the oil pan, open the oil drain bolt and drain the waste oil. When draining the engine oil, try to let the engine oil drip for a period of time, and ensure that the waste oil is drained clean. (the engine oil will produce a lot of impurities through use. If it is not discharged cleanly during replacement, it is easy to block the oil circuit, resulting in poor oil supply and wear of structural parts.

第二步：拆除舊的機油濾芯

Step 2: remove the old engine oil filter element

把舊油容器移至機濾下方，拆下舊的濾芯。注意不要讓廢油弄臟機器內部。

Move the old oil container under the filter and remove the old filter element. Be careful not to let waste oil dirty the inside of the machine.

第三步：機油濾芯安裝前的準備工作

Step 3: preparation before installation of oil filter element

康姆勒發電機廠家技術專家告訴用戶更換新的機濾用不用先往濾芯里面注滿機油。

The technical expert from the manufacturer of komler generator told the user to replace the new filter without filling the filter element with engine oil first.

第四步：安裝新的機油濾芯

Step 4: install a new oil filter element

檢查機油濾芯安裝位置的出油口，清理上面的臟物和殘留的廢油。安裝前，先在出油口位置套上密封環，然后把新的機濾慢慢的擰上去，機濾不要擰的太緊，一般情況下是用手?jǐn)Q緊以后，再用扳手?jǐn)Q3/4圈就可以了。注意裝新濾芯的時候，使用扳手?jǐn)Q不要用力過大，否則容易損壞濾芯內部的密封圈，造成密封效果變差，起不到過濾效果!

Check the oil outlet at the installation position of the oil filter element and clean the dirt and residual waste oil on it. Before installation, first put a sealing ring on the oil outlet, and then screw the new filter slowly. Do not screw the filter too tightly. Generally, after tightening by hand, use a wrench to screw it for 3 / 4 turn. Note: when installing a new filter element, use a wrench and do not use too much force, otherwise it is easy to damage the sealing ring inside the filter element, resulting in poor sealing effect and no filtering effect!

第五步：往機油油箱加注新的機油

Step 5: fill the oil tank with new oil

將新機油注入機油油箱，必要時，要使用漏斗，防止將機油倒在發動機外部。加注完以后，再次檢查發動機下部是否有泄漏。

Fill the oil tank with new oil. If necessary, use a funnel to prevent the oil from pouring out of the engine. After filling, check the lower part of the engine again for leakage.

以上就是今天小編給大家提供的精彩內容，更多的精彩內容請點擊進入我們的官方網站：機油濾芯http://m.dgtmcnc.com

The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: engine oil filter element http://m.dgtmcnc.com