天然氣發電機作為天然氣長輸管道輸氣場站中重要的生產后備電源，在市電失效時，其供電的安全可靠直接關系到天然氣輸氣場站的正常生產。但在實際使用時，仍舊會出現一些問題，導致天然氣發電機組不能正常工作。今天小編就供給系統故障，給大家做一些分析。如下：

As an important production backup power source in natural gas long-distance pipeline gas transmission stations, the safety and reliability of natural gas generators' power supply are directly related to the normal production of natural gas transmission stations in the event of power failure. However, in practical use, there may still be some problems that prevent natural gas generators from working properly. Today, the editor will provide some analysis on system failures for everyone. As follows:

天然氣供給系統功用是：經分離、過濾后的天然氣通過電磁閥進入壓力調節閥，根據天然氣組分，調節到合適壓力，供入天然氣發動機。主要由電磁閥、壓力調節閥、天然氣進氣管和球閥、電動調節閥等相關部件組成。發動機啟動故障時，主要檢查：

The function of the natural gas supply system is that the separated and filtered natural gas enters the pressure regulating valve through an electromagnetic valve, and is adjusted to the appropriate pressure according to the composition of the natural gas before being supplied to the natural gas engine. It mainly consists of solenoid valves, pressure regulating valves, natural gas intake pipes and ball valves, electric regulating valves and other related components. When the engine fails to start, the main checks are:

電磁閥：電磁閥線圈內阻為35Ω，使用萬用表測量，如測量阻值過大或過小，則判斷電磁閥線圈損壞，需進行更換。另外電磁閥還通過壓力繼電器與潤滑油壓低、超速停車裝置相聯動，當超速或潤滑油壓過低時，能自動關閉電磁閥，實現發電機組的安全互鎖。因此判斷電磁閥是否正常，除檢查本身外，還需對相關安全聯鎖裝置進行檢查。

Electromagnetic valve: The internal resistance of the electromagnetic valve coil is 35 Ω. Use a multimeter to measure it. If the resistance value is too high or too low, it is judged that the electromagnetic valve coil is damaged and needs to be replaced. In addition, the solenoid valve is also linked to the low lubricating oil pressure and overspeed shutdown device through a pressure relay. When overspeed or low lubricating oil pressure occurs, the solenoid valve can be automatically closed to achieve safety interlock of the generator set. Therefore, to determine whether the solenoid valve is normal, in addition to checking itself, it is also necessary to inspect the relevant safety interlock devices.

調節閥壓力：天然氣發電機進氣工作壓力為7~9kPa。壓力過高或過低都將會導致發動機啟動故障，因此主要檢查壓力調節閥出口壓力，檢查方法：先慢慢關上出口閥門，檢查出口閥至調壓閥間的壓力，如壓力穩定，說明壓力調節閥正常。如壓力持續升高，則需對調節閥內部膜片進行檢查更換。

Regulating valve pressure: The working pressure of the natural gas generator inlet is 7-9 kPa. Excessive or insufficient pressure can cause engine start-up failures. Therefore, the main inspection is to check the outlet pressure of the pressure regulating valve. The inspection method is to slowly close the outlet valve and check the pressure between the outlet valve and the pressure regulating valve. If the pressure is stable, it indicates that the pressure regulating valve is normal. If the pressure continues to rise, it is necessary to inspect and replace the internal diaphragm of the regulating valve.

燃料混合氣：經空氣濾芯等進入的空氣經燃?xì)饣旌掀骱蟀匆欢ū壤c天然氣形成可燃混合氣，進入燃燒室。如果濃度過濃或過稀，都會導致發動機無法啟動，我們可以通過可燃混合氣調整螺釘來調整可燃混合氣的濃度。

Fuel mixture: The air entering through the air filter and other components is mixed with natural gas in a certain proportion to form a combustible mixture, which then enters the combustion chamber. If the concentration is too high or too low, it will cause the engine to fail to start. We can adjust the concentration of the combustible mixture by using the combustible mixture adjustment screw.

本文來自：焦化氣發電機組更多的內容請點擊：http://m.dgtmcnc.com我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

This article is from: Coking gas generator set. For more content, please click: http://m.dgtmcnc.com We will provide satisfactory service for the questions you ask. Welcome to call us!