上次給大家講了合金尾氣發電機組的冷卻液作用，大家都知道冷卻液久了呢都需要更換，而且半年內至少更換一次，以避免由于冷卻系統內有沉淀而降低冷卻性能。更換冷卻液的另一個原因是避免機組銹蝕的危險，因?yàn)闀r(shí)間一長，銹跡就會降低添加劑的有效性及使水溫傳感器失效。那更換合金尾氣發電機組冷卻液有什么注意事項嗎？今天合金尾氣發電機組廠家就給大家分享一下：

　　Last time I talked to everyone about the role of the coolant in the alloy tail gas generator set. As we all know, the coolant needs to be replaced over time, and it should be replaced at least once every six months to avoid a decrease in cooling performance due to sedimentation in the cooling system. Another reason for replacing the coolant is to avoid the danger of rusting the unit, as over time, rust will reduce the effectiveness of additives and cause the water temperature sensor to fail. Are there any precautions for replacing the coolant of the alloy tail gas generator set? Today, the manufacturer of alloy tail gas generator sets will share with you:

　　機組長期存放時一定要放盡機體及冷卻系統其它附件中的冷卻液。冷卻液排放前，確保機組關閉及機體完全冷卻。一般要求放盡水箱、機體、水泵（如有放水口）、機油冷卻器（如有放水口）、水加熱器（如有放水口）、濾清器中的水。更換冷卻液時，冷卻系統應先用清水沖洗,清洗時一定要等沖出的水很干凈時才行。 確保合金尾氣停機和完全冷卻后，才能加入冷卻液。當發動機溫度依然很高時，不要打開加水口蓋。否則蒸氣或高溫冷卻液可能會噴出。

　　When storing the unit for a long time, it is necessary to drain all the coolant in the body and other accessories of the cooling system. Before discharging the coolant, ensure that the unit is turned off and the body is completely cooled. It is generally required to drain all water from the water tank, machine body, water pump (if any), oil cooler (if any), water heater (if any), and filter. When replacing the coolant, the cooling system should be rinsed with clean water first. When cleaning, be sure to wait until the water flushed out is very clean. Ensure that the alloy exhaust is shut down and completely cooled before adding coolant. Do not open the water inlet cap when the engine temperature is still high. Otherwise, steam or high-temperature coolant may spray out.

　　此外向合金尾氣發電機組水箱中添加冷卻液還須注意如下事項：

　　In addition, the following precautions should be taken when adding coolant to the water tank of the alloy tail gas generator set:

　　1、 向冷卻系統加入冷卻液前，要確保其排放蓋緊閉及排放塞位于正確位置

　　1. Before adding coolant to the cooling system, ensure that the drain cap is tightly closed and the drain plug is in the correct position

　　2、 向系統加入冷卻液時不要太快，以避免系統內形成氣泡斷層

　　2. Do not add coolant to the system too quickly to avoid the formation of bubbles and faults in the system

　　3、 空氣須通過通風口或通過填孔排出。如冷卻系統連接有加熱器，加熱器控制閥須打開，注入時應保持單元內通風

　　3. Air must be discharged through ventilation openings or through filling holes. If the cooling system is connected to a heater, the heater control valve must be opened, and ventilation should be maintained inside the unit during injection

　　4、注入冷卻液時，液面應達到位于填口塞焊接面下5厘米處

　　4. When injecting coolant, the liquid level should reach 5 centimeters below the welding surface of the filler plug

　　5、冷卻液加好后，應注意啟動并預熱機組。同時檢查冷卻液面，如需要，請補滿。

　　5. After adding the coolant, pay attention to starting and preheating the unit. At the same time, check the coolant level and fill it up if necessary.

　　好了，關于合金尾氣發電機組更換冷卻液的注意事項就給大家分享這么多，如果遇到問題可咨詢我們。

　　Alright, that's all for the precautions on replacing the coolant for the alloy tail gas generator set. If you encounter any problems, please feel free to consult us.

　　本文由  合金尾氣發電機組 友情奉獻.更多有關的知識請點擊  http://m.dgtmcnc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the alloy tail gas generator set For more related knowledge, please click http://m.dgtmcnc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.