合金尾氣發電機組啟動后自動停機且無報警，可能由多種原因?qū)е隆Ｒ韵率桥挪楣收系牟襟E及重點檢查點：

　　The automatic shutdown of the alloy tail gas generator set without any alarm after startup may be caused by various reasons. The following are the steps and key checkpoints for troubleshooting:

　　一、檢查氣路系統

　　1、 Check the pneumatic system

　　合金尾氣供應檢查

　　Alloy exhaust gas supply inspection

　　檢查氣瓶閥門是否關閉嚴密，壓力是否正常（可通過壓力表測量）。

　　Check whether the valve of the gas cylinder is tightly closed and whether the pressure is normal (which can be measured by a pressure gauge).

　　檢查進氣管路是否堵塞或空氣濾清器是否清潔。

　　Check if the intake pipe is blocked or if the air filter is clean.

　　檢查燃料管道是否有泄漏，尤其是連接件和接頭處。

　　Check for leaks in the fuel pipeline, especially at the connections and joints.

　　混合氣質量

　　Mixed gas quality

　　通過參數超標保護系統判斷混合氣是否過稀或過濃，必要時調整減壓器或噴閥。

　　Determine whether the mixture is too lean or too rich through the parameter over limit protection system, and adjust the pressure regulator or spray valve if necessary.

　　二、檢查點火系統

　　2、 Check the ignition system

　　點火模塊與線路

　　Ignition module and wiring

　　檢查點火模塊電源指示燈及線束插口是否正常，動力缸線路有無接地故障。

　　Check whether the ignition module power indicator light and harness socket are normal, and whether there is a grounding fault in the power cylinder circuit.

　　檢查火花塞電極間隙及積碳情況，必要時更換火花塞。

　　Check the electrode gap and carbon deposition of the spark plug, and replace the spark plug if necessary.

　　高壓系統檢測

　　High voltage system testing

　　啟動時聽高壓電磁閥是否有“喀噠”聲，檢查高壓線是否漏電。

　　When starting, listen for a "click" sound from the high-voltage solenoid valve and check for any electrical leakage in the high-voltage line.

　　三、檢查控制系統

　　3、 Check the control system

　　傳感器與執行器

　　Sensors and actuators

　　檢查曲軸凸輪軸轉角傳感器、ECU等是否正常工作。

　　Check if the crankshaft camshaft angle sensor, ECU, etc. are working properly.

　　檢查12V/24V電源系統是否穩定，繼電器是否正常。

　　Check if the 12V/24V power system is stable and if the relays are functioning properly.

　　保護系統觸發

　　Protection system triggered

　　查看故障顯示表，確認是否因參數超標（如壓力異常）觸發緊急停機。

　　Check the fault display table to confirm if the emergency stop was triggered due to parameter exceedance (such as abnormal pressure).

　　四、其他檢查項

　　4、 Other inspection items

　　冷卻系統

　　cooling system

　　檢查冷卻水管路是否漏水，風扇是否正常運轉，節溫器是否卡住。

　　Check whether the cooling water pipeline is leaking, whether the fan is running normally, and whether the thermostat is stuck.

　　機械部件

　　mechanical parts

　　聽機組運行聲音，檢查是否有異常敲擊聲或振動，排除機械故障。

　　Listen to the sound of the unit running, check for any abnormal knocking or vibration, and eliminate mechanical faults.

　　五、處理建議

　　5、 Suggestions for handling

　　若上述檢查未發現問題，建議逐步排查燃油系統、熱工保護系統等。

　　If no problems are found during the above inspection, it is recommended to gradually investigate the fuel system, thermal protection system, etc.

　　若故障復雜，需聯系專業人員使用專業設備檢測。

　　If the fault is complex, it is necessary to contact professionals to use professional equipment for testing.

　　本文由  合金尾氣發電機組  友情奉獻.更多有關的知識請點擊  http://m.dgtmcnc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the alloy tail gas generator set For more related knowledge, please click http://m.dgtmcnc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.